- We Are Cable Management Solutions !Hire Us
- Anand Nagar, Ambernath (East),
Cable Tray Manufacturer in Indore & Pithampur
Cable Tray Manufacturer and Supplier in Indore & Pithampur
Industrial belts served: Pithampur · Dewas · Sanwer Road · Mhow · Ujjain · Indore SEZ
Pithampur is central India's main automotive and pharmaceutical cluster, and tray packages there tend to mix heavy ladder runs on the manufacturing side with stainless perforated tray in the formulation blocks.
Indore's inland location keeps the corrosion requirement moderate. Pre-galvanized indoors and hot dip galvanized outdoors covers the non-process scope without over-specifying.
Mitool Equipments Pvt. Ltd. manufactures cable management systems at MIDC Additional Ambernath in Thane district and supplies them throughout Indore & Pithampur. We quote against your cable schedule and tray layout rather than a generic size list — send the drawing with the finish required and the quotation comes back with tray sizes, bends, reducers, coupler plates and supports listed line by line, with a dispatch date.
Cable Tray Range Supplied in Indore & Pithampur
Perforated Cable Tray
Slotted base that lets cable heat escape and allows clamping and hold-down at any point along the run. The highest-volume tray type on most Indore and Pithampur projects.
Ladder Cable Tray
Open rung construction for the heavy end of the cable schedule — feeds to motors, presses, compressors and switchrooms, on wider support centres.
Bolted Rung Ladder Type Cable Tray
Bolted rather than welded rungs, so spacing can be reset at site and individual rungs replaced without cutting the run apart.
Stainless Steel Cable Tray
Supplied in SS304 and SS316 where washdown, process chemistry or chloride exposure rules out a zinc coating.
Wall Mounted Cable Tray Support
Wall and structure brackets sized to carry the tray and the cable load above it, in matching material and finish.
Perforated Cable Tray Accessories
The fittings that make a run continuous: bends, risers, reducers, tees, crosses, coupler plates and clamps, all in the tray's own grade.
What Each Indore & Pithampur Sector Specifies
A starting point for tray selection by application. Final selection follows your cable schedule, fill ratio and support spacing.
| Sector and belt | Typical tray | Usual finish |
|---|---|---|
| Automotive and components Pithampur, Dewas | Ladder tray for press and paint shop power, perforated for control | Pre-galvanized indoors, hot dip for yards |
| Pharmaceutical Pithampur, Indore SEZ | Stainless perforated tray in classified areas | SS304; SS316 for aggressive cleaning chemistry |
| Food and agro processing Dewas, Ujjain | Stainless perforated tray in washdown areas | SS304 |
| Engineering and castings Sanwer Road, Mhow | Ladder tray for furnace and shop power | Hot dip galvanized |
| Textiles Dewas, Indore | Perforated tray in humid process halls | Hot dip galvanized |
Choosing the Right Finish for Indore & Pithampur
Indore and Pithampur sits inland with moderate humidity and no salt-laden air. That is not a trivial detail — it changes the economics of the tray package compared with a coastal site like Mumbai or Mundra.
Where the boundaries fall is a Indore and Pithampur-specific judgement rather than a general rule. The building envelope is the line that matters, and it is worth drawing it explicitly on the tray layout rather than leaving it to be inferred. Across a site at Pithampur, Dewas or Indore SEZ that usually means the tray schedule is split into two or three finish bands rather than quoted at a single grade, and the saving on the lower band normally pays for the upgrade on the higher one.
Pre-galvanized sheet to IS 277, formed after galvanizing, is usually sufficient for runs inside a covered building and is the most economical option. At normal tray thicknesses the zinc protects cut edges by sacrificial action.
Hot dip galvanizing to IS 2629 and IS 4759, applied after fabrication, gives a heavier and more uniform coating that also covers welds and cut edges. Specify it for anything outdoors — rooftop solar, pipe racks, open yards, utility blocks. The monsoon at Indore and Pithampur is long enough that this is the right call for any run not under a roof.
On Indore and Pithampur projects specifically, the runs that get under-specified are the ones that start indoors and finish outside — a feed leaving a shed to a yard-mounted panel, or a rooftop route. The whole run usually gets priced at the indoor finish. It is worth walking the route on the drawing zone by zone before the order goes in — on a automotive and componentspithampur, dewas job around Pithampur or Dewas, that exercise usually changes two or three line items and costs nothing at enquiry stage.
Powder coating is chosen for appearance rather than protection and suits exposed runs in commercial interiors and IT fit-outs. It should sit over a galvanized base wherever moisture is expected, not over bare steel.
Manufacturing Range
| Raw material | Mild steel, stainless steel (SS304 / SS316), aluminium |
| Finish options | Pre-galvanized, hot dip galvanized, powder coated, self-finish |
| Length | 2500 mm – 3000 mm standard; 1000 mm – 3000 mm available |
| Width | 50 mm – 1200 mm (tray); up to 2000 mm on supports |
| Height / side rail | 15 mm – 150 mm |
| Thickness | 1.2 mm – 3 mm |
| Bend | 15 mm – 25 mm |
| Strength class | Light, medium and heavy duty |
| Accessories | Horizontal and vertical bends, reducers, tee and cross sections, coupler plates, clamps, wall mounted supports |
| Supply capacity | 1500 – 2000 metres per week |
| Packing | Loose, nested or in sets as per site requirement |
Tray in India is normally specified to IS 14927 — Part 1 for general requirements, Part 2 for trays and ladder systems including load class and span — with IEC 61537 cited as the international equivalent on multinational projects. Galvanizing is called out as IS 277 for pre-galvanized sheet or IS 2629 and IS 4759 for hot dip. Confirm all three at enquiry stage: standard, load class and support spacing. They have to agree with each other, and settling that before the order costs nothing.
Delivery to Indore & Pithampur
Our works at MIDC Additional Ambernath is 3 days by road from Indore and Pithampur. Deliveries run to Pithampur, Dewas, Sanwer Road, Mhow, Ujjain, Indore SEZ. Trays are bundled and strapped for site handling, and accessories can be packed separately by zone where a project is erected in phases. For larger site packages we can stage dispatch against your erection schedule rather than delivering the full quantity at once.
Send your cable tray schedule for a Indore & Pithampur project
Share the tray layout or bill of quantities with sizes, finish and accessories. You get back a line-by-line quotation with dispatch timing.
Request a Quotation Call +91-251-2621925Cable Tray Questions from Indore & Pithampur Buyers
Do you deliver cable trays across Indore & Pithampur?
Yes. Our works is at MIDC Additional Ambernath, Thane, 3 days by road from Indore and Pithampur, and we dispatch to all its industrial belts including Pithampur, Dewas, Sanwer Road, Mhow, Ujjain. Trays are supplied in standard 2500 mm and 3000 mm lengths, bundled and strapped for site handling.
Which cable tray finish should be specified in Indore and Pithampur?
Indore and Pithampur is inland with no salt-laden air, so pre-galvanized tray to IS 277 is usually adequate for indoor runs inside a covered plant. Specify hot dip galvanized to IS 2629 for outdoor runs, rooftop solar and open yards. Use SS304 where washdown or product contact applies, and SS316 only where process chlorides are present.
Can I save cost by using pre-galvanized tray throughout?
Indoors, usually yes. Outdoors it is a false economy — monsoon exposure will reach the cut edges long before the design life is up. The usual approach at Indore and Pithampur is pre-galvanized inside the building envelope and hot dip galvanized for everything beyond it.
How long does an order take?
Quantity and finish drive it. Hot dip galvanizing is an extra processing stage after fabrication, and stainless is made to order, so both take longer than pre-galvanized. Share the bill of quantities and the dispatch date is confirmed alongside the quotation.
Do you supply test or compliance documentation?
Yes, against the standard your specification names. IS 14927 Part 2 is the usual Indian reference and IEC 61537 the international one. We need the load class and the support spacing from the drawing as well, because the three have to be consistent.
Which tray sizes are available?
50 mm to 1200 mm width, 15 mm to 150 mm side rail height, 1.2 mm to 3 mm thickness and 2500 mm or 3000 mm standard length, in light, medium and heavy duty, with supports to 2000 mm. Non-standard sizes are made to order from your drawing.